Es’hail-2 / P4-A positioning and IOT phase started

Es’hail-2 / P4-A positioning and IOT phase started

Es'hail-2 Mission Patch

Es’hail-2 Mission Patch

Following the successful launch on November 15 of Es’hail-2 on board the SpaceX Falcon 9 launch vehicle, Mitsubishi (MELCO) and Es’hailSat will begin the In Orbit Testing (IOT) program once the satellite has been positioned in a test orbital slot – the positioning should be achieved in the next few days.

The IOT phase will take a few months, during which time the amateur radio payload will not be turned on.

AMSAT-DL will be commissioning the Amateur transponder ground station in Doha with the Es’hailSat control team.

Once IOT is complete, the satellite will be moved to the final orbital slot at 26 degrees and there will be an announcement by AMSAT-DL when the transponders are available for use.

Before this announcement, no attempt should be made to use the transponders as any interference to the test program will delay the release and if excessive interference is seen may cause the satellite owners not to make the facility available for amateur use.

Source AMSAT-DL
https://amsat-dl.org/p4a-positionining-and-iot
https://twitter.com/amsatdl

Es’hail-2 geostationary satellite information including video of a presentation on the transponders
https://amsat-uk.org/2018/11/05/eshail-2-geostationary-transponders/

Coming soon Es’hail-2 WebSDR https://eshail.batc.org.uk/

Get The Details…

m5aka

AMSAT-UK

Powered by WPeMatico

JY1SAT Launch Information and Dashboard

JY1SAT Launch Information and Dashboard

 

JY1SAT CubeSat

JY1Sat is an enhanced 1U FUNcube. It has been developed for the Crown Prince Foundation in Jordan. The spacecraft has been named in honour of the Crown Prince’s grandfather, King Hussein, who operated using his personal amateur radio callsign which was simply JY1.

In addition to the usual suite of FUNcube capabilities it will also be capable of downlinking images in SSDV format.  This image format, developed by Phil Heron, MI0VIM, for use in High Altitude Balloons, is now also being used from lunar orbit by AO-94.

The telemetry downlink frequency is 145.840 MHz, this will use the usual FUNcube standard 1k2 BPSK format. The linear transponder, for Single Sideband (SSB) and CW modes, will downlink on 145.855-145.875 MHz and uplink on 435.100-435.120 MHz. The transponder is inverting so Lower Sideband (LSB) should be used on the uplink and Uppersideband (USB) on the downlink.

A new Dashboard has been developed for this mission and is available for download here:

This will operate in exactly the same manner as those developed for previous missions and general set-up information can be downloaded here: Dashboard Guidance

A brand new Data Warehouse has also been created. This can be used to view the telemetry from ALL of the FUNcube missions. This can his can viewed here http://data2.amsat-uk.org/

SSO-A Mission Patch

SSO-A Mission Patch

This mission will be one of the payloads on the Spaceflight SSO-A mission. This is currently scheduled to lift-off on Monday, November 19, 2018 at 18:32 GMT from the Vandenberg Air Force base in California. This launch is expected to have more than sixty other payloads.

The deployment time for JY1SAT has been advised as 4 hours 31 minutes and 54.5 seconds after launch. This means that, allowing for the pre-programmed delay of 30 minutes between deployment from the POD and the release of the antennas, the first downlink signals cannot be expected until approximately 23:34 GMT on November 19.

Watch the launch at https://www.youtube.com/watch?v=PJkRM5QQDAA

Here are some initial pre-launch TLEs which we believe will be accurate for at least the first few orbits.

JY1-Sat
1 50001U 18001A 18323.01450000 .00000000 00000-0 30100-5 0 9992
2 50001 97.7750 30.5000 0012840 225.0000 124.7930 15.00300000 11

Provisional SatPC32 Doppler.sqf data for tracking JY1SAT and other Amateur Radio satellites on SSO-A at https://gist.github.com/magicbug/cf23cfca3a6ec9902d8dd9326a9249ea

Initial indications are that the spacecraft will be over NE Australia at power-up.

The start-up mode, as usual, is low power telemetry only and we will be really looking forward to receiving reports  and telemetry. So please, either upload the data from the Dashboard to the Warehouse in the usual way, or send a quick email to operations@funcube.org.uk

Get The Details…

m5aka

AMSAT-UK

Powered by WPeMatico